Jlg Boom Lift Won't Move

Are you having trouble getting your Jlg Boom Lift to move? It can be a perplexing issue, but thankfully there are several possible causes and solutions. With the help of experienced mechanics and a little bit of detective work, you can uncover the mystery and get your lift up and running again.

Troubleshooting Your Jlg Boom Lift Won't Move Problem

If you’re dealing with a Jlg Boom Lift that won't move, it can be a perplexing issue. Fortunately, there are a few possible causes and solutions to get you back on track. From inspecting the hydraulic system to checking the engine, our guide will help you identify and resolve the Jlg Boom Lift won't move problem. With the right steps and the assistance of experienced mechanics, you can have your lift running again in no time.

Below is a table of common causes and potential solutions for when your Jlg Boom Lift won’t move:

Cause Solution
Clogged Filter Clean or replace the filter
Low Hydraulic Pressure Check the pump and pressure relief valve
Engaged Parking Brake Release the parking brake
Faulty Electrical System Check the wiring, circuit breaker, and relays
Faulty Engine Check the fuel system and spark plugs

Battery

A dead or weak battery is one of the most common causes of a Jlg Boom Lift not moving. If the battery is not providing enough power, the boom lift will not be able to move. To check the battery’s power, use a multimeter to measure the voltage. If the voltage is below 12.5, the battery needs to be replaced.

Faulty Contactor

A faulty contactor can also prevent a Jlg Boom Lift from moving. A contactor is a motorized switch that controls the power supply to the lift. If it is malfunctioning, it can prevent the lift from moving. To test the contactor, use a multimeter to check the voltage while the lift is running. If the voltage drops, the contactor needs to be replaced.

Dirty Filters

Dirty filters can also be the culprit. When the filters become too dirty, they can block the flow of oil and prevent the lift from moving. To check the filters, remove them and inspect for any signs of dirt or debris. If the filters are clogged, they need to be replaced.

Lack of Hydraulic Pressure

A lack of hydraulic pressure is another possible cause of a Jlg Boom Lift not moving. If the hydraulic pressure is too low, the lift will not be able to move. To check the hydraulic pressure, use a pressure gauge to measure the pressure in the system. If the pressure is below the manufacturer’s recommended level, the hydraulic system needs to be serviced.

In conclusion, there are several possible causes of a Jlg Boom Lift not moving, ranging from a dead battery to a lack of hydraulic pressure. To troubleshoot the issue, it is important to use the right tools and perform a thorough inspection. With the help of experienced mechanics and a bit of detective work, you can uncover the mystery and get your lift up and running again.

Key Takeaways for Troubleshooting a Jlg Boom Lift Won't Move Problem

  • Clean or replace the filter if it is clogged.
  • Check the pump and pressure relief valve if the hydraulic pressure is low.
  • Release the parking brake if it is engaged.
  • Check the wiring, circuit breaker, and relays if there is a faulty electrical system.
  • Check the fuel system and spark plugs if the engine is faulty.
  • Use a multimeter to check the battery's power if the battery is dead or weak.
  • Use a multimeter to check the voltage if the contactor is faulty.
  • Remove the filters and inspect for dirt or debris if they are clogged.
  • Use a pressure gauge to measure the pressure in the system if the hydraulic pressure is low.

Get Your Jlg Boom Lift Moving Again with These Troubleshooting Tips

If you find yourself in a situation where a Jlg Boom Lift won't move, there are several potential causes that can be quickly identified and resolved. From filters that need to be replaced to a faulty contactor or low hydraulic pressure, experienced mechanics can help you troubleshoot the issue and get your lift up and running again.

Remember to always use the right tools and perform a thorough inspection before attempting any repairs. Clean or replace the filter if it is clogged, check the pump and pressure relief valve if the hydraulic pressure is low, and release the parking brake if it is engaged. Additionally, check the wiring, circuit breaker, and relays if there is a faulty electrical system, and check the fuel system and spark plugs if the engine is faulty.

Finally, use a multimeter to check the battery's power if the battery is dead or weak, use a multimeter to check the voltage if the contactor is faulty, remove the filters and inspect for dirt or debris if they are clogged, and use a pressure gauge to measure the pressure in the system if the hydraulic pressure is low. With these tips, you can get your Jlg Boom Lift moving again in no time.

Rate this post
Categories JLG

Leave a Comment

×

Ask an Expert

*Follow this page every hour. We will respond to you regarding the comment you make or the question you ask.